- Recent Posts

На території України запустили нішевий каталог спеціалізованих платформ

ReveScuNc — Sat, 21 Mar 2026 08:10:41 +0000

Український сегмент мережі Інтернет отримав черговий корисний ресурс — навігатор по сайтам, створений для агрегації різнопланові українські сайти. Цей інтернет-майданчик збирає гіперпосилання на джерела, що розкривають широкий спектр тем. Каталог включає ресурси як загальнонаціонального рівня, так і ті, що фокусуються на розвитку локальних територій. Основна мета проєкту — запропонувати простий стартовий майданчик для інтернет-аудиторії, які шукають актуальні місцеві медіа на будь-який смак: починаючи від оперативних зведень і політикуму до історичних розвідок, молодіжної тематики, стилю життя, громадської діяльності та публіцистики. Цей ресурс розрахований на масового відвідувача та відкритий до співпраці з медіа, журналістами та рекламодавцями, які прагнуть бути помітними в інформаційному просторі України

Emfimastic - how to clean it when used in assembly?

OndraK — Tue, 08 Oct 2024 07:42:50 +0000

Hi, if any of you wonder, how keep the surface of your Dingo clean, when using the emfimastic - here is one tip for you:

Immediatelly after the connection is made with the emfimastic, which is still not cured - that´s important not to let it cure! - use C6000 Thinner and some old towel to clean the rest of emfimastic, which is out of this connection. If you let it cure, then it will be a really difficult to get rif off it...

Polini 250

OndraK — Fri, 12 Jan 2024 11:57:33 +0000

Please, take a look at some pictures, how was Polini 250 installed on our Dingo!

Vitorazzi Cosmos

OndraK — Fri, 12 Jan 2024 11:49:34 +0000

Please, take a look at some pictures, how was Vitorazzi Cosmos installed on our Dingo!

39 37 38 36

Polini Thor 303

OndraK — Fri, 12 Jan 2024 09:58:21 +0000

Please, take a look at some pictures, how was Polini Thor 303 installed on our Dingo!

35 31 27 29 28 34 30 33 26 25 32

EOS Quattro engine

OndraK — Fri, 12 Jan 2024 09:44:40 +0000

Please, take a look at some pictures, how was the 4-stroke EOS Quattro engine installed on our Dingo 😉

23 24 22 21 18 19 20

Vitorazzi Moster 185

OndraK — Fri, 12 Jan 2024 09:20:42 +0000

Please, take a look at some pictures, how was Vitorazzi Moster 185 installed on our Dingo! 😉

17 16 15 14 13 12 11 10 9 8 7 6

RE: Control system in fuselage

OndraK — Tue, 25 Jul 2023 07:45:33 +0000

Hi, yes, absolutely! Please, take a look into the manual, page 227, there is a step with the intallation of the elevator push rod 2 and PETF Tubes. And then on the page 285, there´s a step where you need to install the rest of control systems.

RE: Control system in fuselage

RobH — Mon, 24 Jul 2023 16:15:36 +0000

Sorry I've not got that far yet. I did have a quick scan though the Fuselage manual (there's a lot of pages in that one 🤣) and I think I saw the elevator pushrod has to go in, not sure what else.

RE: Surface treatment of hinges

RobH — Mon, 24 Jul 2023 16:09:32 +0000

I used an aerosol primer called ProXL Spectro Prime, which is available in a selection of colours. It's a self-etch primer which seems to stick well to the aluminium as long as it's thoroughly degreased first. I over-coated it with ProXL Matt Lacquer, which is scratch, UV & petrol resistant, also in an aerosol. I used 3 coats of each, only allowing about five minutes between each coat. They are both 1K paints, so something like acetone would strip them both off. I tried various solvents, looking for something that would clean up the mastic used in the Dingo kit but not attack the paint, and the best thing I found was Primus "Power Fuel". It's like a highly refined petrol/gasoline for use in camping cookers. The paint stands up to it ok, as long as you don't rub too hard or leave it on too long...

I did consider 2K paints, which should give a harder finish and stand up better to solvents, but they have some disadvantages. They're 2-component paints where a hardener is mixed with a base. They are available in aerosols, but once activated they have to be used up in a fairly short timescale. Also I believe some of the ingredients are more toxic than in 1K paints, and I don't have proper spray facilities.

I'd suggest doing some tests with what is available in your area, and satisfy yourself that the products & process are satisfactory for what you want